E2IMAGE(8)E2IMAGE(8)NAMEe2image - Save critical ext2/ext3/ext4 filesystem metadata to a file
SYNOPSISe2image [ -rsIQa ] device image-file
DESCRIPTION
The e2image program will save critical ext2, ext3, or ext4 filesystem
metadata located on device to a file specified by image-file. The
image file may be examined by dumpe2fs and debugfs, by using the -i
option to those programs. This can assist an expert in recovering cat‐
astrophically corrupted filesystems. In the future, e2fsck will be
enhanced to be able to use the image file to help recover a badly dam‐
aged filesystem.
If image-file is -, then the output of e2image will be sent to standard
output, so that the output can be piped to another program, such as
gzip(1). (Note that this is currently only supported when creating a
raw image file using the -r option, since the process of creating a
normal image file, or QCOW2 image currently requires random access to
the file, which cannot be done using a pipe. This restriction will
hopefully be lifted in a future version of e2image.)
It is a very good idea to create image files for all of filesystems on
a system and save the partition layout (which can be generated using
the fdisk -l command) at regular intervals --- at boot time, and/or
every week or so. The image file should be stored on some filesystem
other than the filesystem whose data it contains, to ensure that this
data is accessible in the case where the filesystem has been badly dam‐
aged.
To save disk space, e2image creates the image file as a sparse file, or
in QCOW2 format. Hence, if the sparse image file needs to be copied to
another location, it should either be compressed first or copied using
the --sparse=always option to the GNU version of cp. This does not
apply to the QCOW2 image, which is not sparse.
The size of an ext2 image file depends primarily on the size of the
filesystems and how many inodes are in use. For a typical 10 gigabyte
filesystem, with 200,000 inodes in use out of 1.2 million inodes, the
image file will be approximately 35 megabytes; a 4 gigabyte filesystem
with 15,000 inodes in use out of 550,000 inodes will result in a 3
megabyte image file. Image files tend to be quite compressible; an
image file taking up 32 megabytes of space on disk will generally com‐
press down to 3 or 4 megabytes.
RESTORING FILESYSTEM METADATA USING AN IMAGE FILE
The -I option will cause e2image to install the metadata stored in the
image file back to the device. It can be used to restore the filesys‐
tem metadata back to the device in emergency situations.
WARNING!!!! The -I option should only be used as a desperation measure
when other alternatives have failed. If the filesystem has changed
since the image file was created, data will be lost. In general, you
should make a full image backup of the filesystem first, in case you
wish to try other recovery strategies afterwards.
RAW IMAGE FILES
The -r option will create a raw image file instead of a normal image
file. A raw image file differs from a normal image file in two ways.
First, the filesystem metadata is placed in the proper position so that
e2fsck, dumpe2fs, debugfs, etc. can be run directly on the raw image
file. In order to minimize the amount of disk space consumed by a raw
image file, the file is created as a sparse file. (Beware of copying
or compressing/decompressing this file with utilities that don't under‐
stand how to create sparse files; the file will become as large as the
filesystem itself!) Secondly, the raw image file also includes indi‐
rect blocks and directory blocks, which the standard image file does
not have, although this may change in the future.
Raw image files are sometimes used when sending filesystems to the
maintainer as part of bug reports to e2fsprogs. When used in this
capacity, the recommended command is as follows (replace hda1 with the
appropriate device):
e2image-r /dev/hda1 - | bzip2 > hda1.e2i.bz2
This will only send the metadata information, without any data blocks.
However, the filenames in the directory blocks can still reveal infor‐
mation about the contents of the filesystem that the bug reporter may
wish to keep confidential. To address this concern, the -s option can
be specified. This will cause e2image to scramble directory entries
and zero out any unused portions of the directory blocks before writing
the image file. However, the -s option will prevent analysis of prob‐
lems related to hash-tree indexed directories.
Note that this will work even if you substitute "/dev/hda1" for another
raw disk image, or QCOW2 image previously created by e2image.
QCOW2 IMAGE FILES
The -Q option will create a QCOW2 image file instead of a normal, or
raw image file. A QCOW2 image contains all the information the raw
image does, however unlike the raw image it is not sparse. The QCOW2
image minimize the amount of disk space by storing data in special for‐
mat with pack data closely together, hence avoiding holes while still
minimizing size.
In order to send filesystem to the maintainer as a part of bug report
to e2fsprogs, use following commands (replace hda1 with the appropriate
device):
e2image-Q /dev/hda1 hda1.qcow2
bzip2 -z hda1.qcow2
This will only send the metadata information, without any data blocks.
However, the filenames in the directory blocks can still reveal infor‐
mation about the contents of the filesystem that the bug reporter may
wish to keep confidential. To address this concern, the -s option can
be specified. This will cause e2image to scramble directory entries
and zero out any unused portions of the directory blocks before writing
the image file. However, the -s option will prevent analysis of prob‐
lems related to hash-tree indexed directories.
Note that QCOW2 image created by e2image is regular QCOW2 image and can
be processed by tools aware of QCOW2 format such as for example qemu-
img.
You can convert a qcow2 image into a raw image with:
e2image-r hda1.qcow2 hda1.raw
This can be useful to write a qcow2 image containing all data to a
sparse image file where it can be loop mounted, or to a disk partition.
Note that this may not work with qcow2 images not generated by e2image.
INCLUDING DATA
Normally e2image only includes fs metadata, not regular file data. The
-a option can be specified to include all data. This will give an
image that is suitable to use to clone the entire FS or for backup pur‐
poses. Note that this option only works with the raw or QCOW2 formats.
AUTHORe2image was written by Theodore Ts'o (tytso@mit.edu).
AVAILABILITYe2image is part of the e2fsprogs package and is available from
http://e2fsprogs.sourceforge.net.
SEE ALSOdumpe2fs(8), debugfs(8)E2fsprogs version 1.42.8 June 2013 E2IMAGE(8)
